The KVS Series of power amplifiers from Crown represent a new era in affordable, quality power amplification. The line consists of four models in a uniform, rugged chassis, incorporating the best of reliable design principles and innovative features. Modern power amplifiers are sophisticated pieces of engineering products, which are capable of producing extremely high power. If we need to have them providing years of reliable service, we must treat them seriously and have them correctly installed. In addition, KVS Series amplifiers include a number of features which require some explanation before they can be used to their maximum advantage. Please take time to study this manual so that you can obtain the best possible service from your amplifier.
Features
· Simple, reliable design incorporates many popular features.
· Housed in a rugged, all-steel 2U chassis.
· Efficient forced-air fans prevent excessive thermal buildup.
· Electronically balanced XLR inputs. Touch-proof binding post and Speakon® outputs.
· Features precision detented level controls, power switch, power LED, and six LEDs which indicate signal, clip, and fault for each channel.
Specifications
Minimum Guaranteed Power 1kHz
Stereo, 4 ohms (per ch.)
Stereo, 8 ohms (per ch.)
Bridge, 8 ohms
Stereo, 4ohms (per ch.) more than 1 mins
Bridge, 8ohms more than 1 mins
450W
300W
900W
350W
700W
Performance
Signal Response (1W)
Total Harmonic Distortion (THD)
Intermodulation Distortion (IMD) 60 Hz and 7 kHz at 4:1, from full rated
output to –30 dB
Slew Rate
Voltage Gain
Damping Factor (8ohms), 10Hz - 400Hz
Signal-to-Noise Ratio (below rated power, 20 Hz to 20 kHz, A weighted)
Crosstalk (below rated power)
At 1 kHz
At 20 kHz
Input Sensitivity (full rated power, 8ohms)
Input Impedance (nominal) Balanced
20Hz - 20kHz, +0/-1dB
< 0.5%, 20 Hz - 20kHz
= / < 0.35%
>10V/us
29dB
> 200
> 100 dB
–75 dB
–59 dB
0.775V or 1.4V
20k ohms
Connectors, Controls and Indicators
Input Connectors
Output Connectors (Speaker Connectors)
Front Panel Controls
Rear Panel Controls
Power Indicator
Signal Indicator
Clip (peak) Indicator
Fault Indicator
Cables
One balanced XLR
4-POLE Speakon® and one pair Binding Post per channel
Power on/off switch, one gain control per channel
Output mode switch: stereo (dual), parallel or bridge Input sensitivity switch: 0.775V
or 1.4V
Blue and Green LED
One green LED per channel
One yellow LED per channel
One red LED per channel
Adaptor: 10A, 250V Cables: CCC 3x1.5mm2
Construction
Protection
Ventilation
Cooling
Dimensions (W x H x D)
Net Weight
Shipping Weight
Protection against short circuits, no-load, on/off muting, RF interference. Stable into
reactive or mismatched loads
Flow-through ventilation from front to back
Internal heat sinks with forced air. Fan cooled, speed regulated, thermal protection
19”x3.5”x15.6” (482 mm x 89 mm x 395 mm)
18.2 lb (8.2 kg)
22.5 lb (10.2 kg)
Two-channel, 750W @ 4Ω Power Amplifier
Two-channel, 1000W @ 4Ω Power Amplifier
Two-channel, 1450W @ 4Ω Power Amplifier
Quy định hình thức thanh toán
Chính sách vận chuyển & giao nhận
Chính sách bảo hành
Chính sách bảo mật thông tin
CHI NHÁNH VĂN PHÒNG HÀ NỘI 404 Trần Khát Chân, phường Thanh Nhàn, quận Hai Bà Trưng, Hà Nội. Phone: (04) 3728 2727 | Fax: (04) 3728 2727