|
Physical
|
|
|
Head:
|
Length: 440 mm (17.4 in.)
Width: 392 mm (15.5 in.)
Height: 167 mm (6.6 in.)
Dry Weight: 13.8 kg (30.5 lbs.)
|
|
Base:
|
Length: 664 mm (26.2 in.)
Width: 392 mm (15.5 in.)
Height: 939 mm (37.0 in.)
Dry weight: 35 kg (77.2 lbs.) incl. two empty 25 l drums
|
|
Performance
|
Max. fog output (approx.): 700 m3 per minute per head
Max. operating time at full output (approx.): 60 minutes (full 16-head system)
Operating time: Continuous, automatic level adjustment
Warm-up time (approx.): 9 minutes
|
|
Control and Programming
|
Control options: Onboard control panel, DMX
Instant or timer-controlled variable output
Output is proportional for all levels above 12%
DMX channels: 1 per head, maximum 16
Protocol: USITT DMX512/1990
Optional digital remote control: For limited control
|
|
Construction
|
Housing: Steel & aluminum
Heat exchanger: 1500 W, direct thermal protection
|
|
Fluid System
|
Fluid pump: Low pressure pump in Base Unit supplies constant 2.5 bar pressure
Pump (EP5) in Head Unit increases 2.5 bar inlet pressure to 16 bar
Solenoid valve in Head Unit for instant cut-off
Onboard fluid capacity: 2 x 25 l
Fluid consumption at peak output: 120 ml per minute per head
|
|
Installation
|
Orientation (Head): Any
Orientation (Base): Floor mount only (On wheels)
|
|
Connections
|
DMX data: 3-pin and 5-pin XLR sockets
Remote control: 3-pin locking XLR
Power cable entry (Base): 3-pin IEC male socket
Power cable entry (Head): Hard-wired
|
|
Electrical
|
AC power (EU models): 220-240 V nominal, 50 Hz
AC power (US models): 110-120 V nominal, 60 Hz
Main fuse (220-240 V power), Head Unit: 10 A
Main fuse (110-120 V power), Head Unit: 15 A
Main fuse (220-240 V power), Base Unit: 3.15 AT (slow blow)
Main fuse (110-120 V power), Base Unit: 6.3 AT (slow blow)
|
|
Typical Power and Current
|
|
|
Head Unit:
|
|
|
US model:
|
110 V, 60 Hz: 1093 W, 9.93 A
115 V, 60 Hz: 1195 W, 10.4 A
120 V, 60 Hz: 1301 W, 10.84 A
|
|
EU model:
|
220 V, 50 Hz: 1361 W, 6.18 A
230 V, 50 Hz: 1488 W, 6.47 A
240 V, 50 Hz: 1620 W, 6.8 A
Measurements made at nominal voltage. Allow for a deviation of +/- 10%.:
|
|
Base Unit:
|
|
|
US model:
|
110 V, 60 Hz: 228 W, 2.07 A
115 V, 60 Hz: 250 W, 2.17 A
120 V, 60 Hz: 272 W, 2.27 A
|
|
EU model:
|
220 V, 50 Hz: 210 W, 0.95 A
230 V, 50 Hz: 229 W, 1 A
240 V, 50 Hz: 250 W, 1.04 A
Measurements made at nominal voltage. Allow for a deviation of +/- 10%.:
|
|
Thermal
|
Maximum ambient temperature (Ta max.): 40° C
Exterior surface temperature, steady state: 50° C
Max. nozzle temperature: 200° C
|
|
Approvals
|
EU safety: EN 50 081-1, EN 50 082-1
EU safety: EN 60 335-1 (1995)
|
|
Included Items
|
Hard wired mains cable 2 m (head)
M8 x 13 mm safety eye (head): P/N 08131901
Fluid line 'tee' piece 10 mm x 10 mm x 6 mm (head): P/N 26460790
Fluid line 6 mm x 10 m (head): P/N 62520020
Container 25 l (x2): P/N 34300529
Fluid line 10 mm x 30 m (x2): P/N 14026021
Power cable 1.5 m IEC w/o end plug: P/N 11501012
Blanking plug 10 mm push In: P/N 26460740
Terminator, 3 pin male hydra: P/N 56250080
Terminator, 3 pin female hydra: P/N 56250090
User manual: P/N 35000194
|
|
Accessories
|
Pro Smoke Super (ZR Mix) fluid
Pro Smoke High Density (SP Mix) fluid
Regular DJ (DJ mix) fluid
Pro Steam Simulation (AA) fluid
I-fog fluid
Digital Multi-function Remote Control: P/N 92765026
Hydra Termination Plug (Male): P/N 56250080
Hydra Termination Plug (Female): P/N 56250090
Self-seal connector, 2 x 6 mm m/f, valved: P/N 92620007
Self-seal connector, 2 x 10 mm m/f, valved: P/N 92620008
30 m length of 10 mm tubing: P/N 92620010
Straight-through connector, 2 x 10 mm: P/N 92620009
|
|
Ordering Information
|
Jem Hydra Base Unit, 110 V: P/N 92250300
Jem Hydra Base Unit, 240 V: P/N 92250200
Jem Hydra Head Unit, 110 V: P/N 92250500
Jem Hydra Head Unit, 240 V: P/N 92250400
Jem Hydra 1.8 240V: P/N 92251000
Jem Hydra 1.8, 110V: P/N 92251050
Jem Hydra 1.16, 240V: P/N 92251100
Jem Hydra 1.16, 110V: P/N 92251150
Jem Hydra 1.4, 240V: P/N 92251200
Jem Hydra 1.4, 110V: P/N 92251250
|