MARTINMartin RDM 5.5 Splitter

Martin RDM 5.5 Splitter


The Martin RDM 5.5 Splitter is the perfect companion to any controller or DMX/RDM device. The main purpose of the Martin 5.5 Splitter is to maintain proper data over long or several runs of DMX signal. The Splitter boosts the weak DMX signal to its original output level before it becomes too low to be read by DMX devices. Disruption of DMX is often caused by bad cables or bad connections. The Martin RDM 5.5 Splitter will help to rectify the signal.

·       5-pin XLR Input and Outputs DMX-RDM E1.20 Splitter/Booster

·       Opto-isolated DMX Output ports

·       Rack, truss and wall mountable


·       DMX Splitter / Booster

·       Opto-isolated DMX Output ports

·       DMX loop through port with built-in termination

·       5-pin XLR Input and Outputs

·       RDM E1.20 compliant

·       Optimized for Martin fixture firmware upload

·       Universal power supply

·       PowerCon connectors in/out for easy daisy-chaining

·       Rack, truss and wall mountable

·       Lightweight yet robust construction



Depth: 125 mm (5.0 in.)

Width: 220 mm (8.7 in.)

Height: 45 mm (1.8 in.)

Weight: 0.9 kg (2.0 lbs.)

Data signal



Electrical standard: EIA-485

Recommended cable type: STP (Shielded Twisted Pair)

Recommended cable gauge: 22 or 24 AWG


Housing: Aluminum

Finish: Electrostatic powder-coated


Data input: 3-pin XLR male

Data throughput (not amplified or branched): 3-pin XLR female

Data outputs (optically isolated and amplified): 5 x 3-pin XLR female

AC power input: 1.2 m cable tail with US-type (NEMA-5-15) power plug


AC power: 100-240 V nominal, 50/60 Hz

Power supply unit: Auto-ranging electronic switch-mode

Typical total power consumption: 4 W

Power consumption figures are typical, not maximum. Allow for +/-10% variation.:


Maximum ambient temperature (Ta max.): 55° C

Minimum ambient temperature (Ta min.): -30° C


EU safety: EN 60950-1

EU EMC: EN 55022, EN 55024, EN 55103-1, EN 55103-2

US safety: UL 508

US EMC: FCC Part 15 Class A

Canadian safety: CAN/CSA C22.2 No. 14

Canadian EMC: ICES-003 Class A

Australia/NZ: C-TICK N4241

Included Items

4 x screws to join two devices for rack mounting

2 x L-brackets + 8 x screws for 19-inch rack mounting two Splitters (1U) or surface mounting

Neutrik PowerCon NAC3FCA male input connector


Neutrik PowerCon NAC3FCA power input connector, cable mount, blue: P/N 05342804

Neutrik PowerCon NAC3FCB power output connector, cable mount, light grey: P/N


Half-coupler clamp: P/N 91602005

G-clamp: P/N 91602003

Quick trigger clamp: P/N 91602007

Safety cable, safe working load 50 kg: P/N 91604003

3-pin male XLR to 5-pin female XLR adaptor: P/N 11820004

5-pin male XLR to 3-pin female XLR adaptor: P/N 11820005

5-pin male XLR to male RJ-45 adapter: P/N 11840111

5-pin female XLR to male RJ-45 adapter: P/N 11840112

Related Items

Martin RDM 5.5 Splitter™: P/N 90758150

Ordering Information

Martin RDM 5.5 Splitter™: P/N 90758150